Documentation | Community | Downloads

Cumulus RMP 3.3.2 Release Notes

Avatar
Pete Bratach
Follow

Overview

These release notes support Cumulus RMP 3.3.2 and describe currently available features and known issues.

Cumulus RMP 3.3.2 supports these features and is available on the Penguin Computing Arctica 4804IP-RMP out-of-band switch.

Stay up to Date 

  • Please sign in and click Follow above so you can receive a notification when we update these release notes.
  • Subscribe to our product bulletin mailing list to receive important announcements and updates about issues that arise in our products.
  • Subscribe to our security announcement mailing list to receive alerts whenever we update our software for security issues.

{{table_of_contents}}

What's New in Cumulus RMP 3.3.2

Cumulus RMP 3.3.2 includes bug fixes only.

Installing Version 3.3.2

If you are upgrading from version 3.0.0 or later, use apt-get to update the software.

  1. Run apt-get update.
  2. Run apt-get upgrade.
  3. Reboot the switch.

New Install or Upgrading from Versions Older than 3.0.0

If you are upgrading from a version older than 3.0.0, or installing Cumulus RMP for the first time, download the Cumulus RMP 3.3.2 installer for Broadcom switches from the Cumulus Networks website, then use ONIE to perform a complete install, following the instructions in the user guide.

Note: This method is destructive; any configuration files on the switch will not be saved, so please copy them to a different server before upgrading via ONIE.

Important! After you install, run apt-get update, then apt-get upgrade on your switch to make sure you update Cumulus RMP to include any important or other package updates.

Documentation

You can read the technical documentation here.

Issues Fixed in Cumulus RMP 3.3.2 Update 2017-07-14

Cumulus Networks has made important package updates available for Cumulus RMP 3.3.2 that resolve the issues listed below. These fixes were applied to the Cumulus Networks repository on July 14, 2017.

Cumulus Networks strongly recommends you upgrade your Cumulus RMP distribution to avoid these issues (do not do a binary install). Follow these steps:

  1. Run apt-get update.
  2. Run apt-get upgrade. 
Release Note ID Summary Description
  
RN-637 (CM-16222)		 Cannot configure VLAN filtering/pruning using NCLU

Running net add interface swp# bridge vids <vid> does not add a bridge-vids configuration under an interface.

This issue has been fixed in the July 14, 2017 update release to Cumulus RMP 3.3.2.
  
RN-638 (CM-16966)		 NCLU netd service crashes if sysname is missing in LLDP output

If the sysname information is not included in the LLDP peer information, netd crashes when running net show interface.

This issue has been fixed in the July 14, 2017 update release to Cumulus RMP 3.3.2.
  
RN-639 (CM-12534)		 `netshow int all -j` returns traceback AttributeError: 'super' object has no attribute 'stp'

If a bridge is configured with STP disabled, the netd daemon returns a traceback error.

This issue has been fixed in the July 14, 2017 update release to Cumulus RMP 3.3.2.

Issues Fixed in Cumulus RMP 3.3.2

The following is a list of issues fixed in Cumulus RMP 3.3.2 from earlier versions of Cumulus RMP.

Release Note ID Summary Description

RN-632 (CM-16783)		 rsyslog stops logging after 4M filesize after upgrade to 3.3.1 

A change in the upgrade process from earlier releases caused a necessary file to be removed, preventing logging from occurring correctly. Customers upgrading to Cumulus RMP 3.3 or later from either Cumulus RMP 3.0.x or 3.1.x should check that the /etc/logrotate.d/ryslog file exists. If it does not, reinstall rsyslog with the following command:

apt-get -o DPkg::options::=--force-confmiss --reinstall install rsyslog

This issue is fixed in Cumulus RMP 3.3.2.

RN-634 (CM-16292)		 net show interface slow to return results 

The NCLU command net show interface takes approximately 9 seconds to return results.

This issue is fixed in Cumulus RMP 3.3.2.

RN-635 (CM-15954)		 rmp/3.2.1 - knet link txq status reports stopped for unit 0 ports, HOL_DROPs accruing for affected xe port An issue was found on Broadcom switches running Cumulus RMP, where the hardware was not passing the queued packets, causing the queues to be suspended. This issue has been fixed in Cumulus RMP 3.3.2.

Known Issues in Cumulus RMP 3.3.2

Issues are categorized for easy review. Some issues are fixed but will be available in a later release.

Release Note ID Summary Description

RN-56 (CM-343)		 IPv4/IPv6 forwarding disabled mode not recognized

If either of the following is configured:

net.ipv4.ip_forward == 0

or:

net.ipv6.conf.all.forwarding == 0

The hardware still forwards packets if there is a neighbor table entry pointing to the destination.

RN-120 (CM-477)		 ethtool LED blinking does not work with switch ports Linux uses ethtool -p to identify the physical port backing an interface, or to identify the switch itself. Usually this identification is by blinking the port LED until ethtool -p is stopped.

This feature does not apply to switch ports (swpX) in Cumulus RMP.

RN-121 (CM-2123)		 ptmd: When a physical interface is in a PTM FAIL state, its subinterface still exchanges information Issue:
When ptmd is incorrectly in a failure state and the Zebra interface is enabled, PIF BGP sessions are not establishing the route, but the subinterface on top of it does establish routes.

If the subinterface is configured on the physical interface and the physical interface is incorrectly marked as being in a PTM FAIL state, routes on the physical interface are not processed in Quagga, but the subinterface is working.

Steps to reproduce: 
cumulus@switch:$ sudo vtysh -c 'show int swp8' 
Interface swp8 is up, line protocol is up 
PTM status: fail
index 10 metric 1 mtu 1500 
 flags: <UP,BROADCAST,RUNNING,MULTICAST>
 HWaddr: 44:38:39:00:03:88 
 inet 12.0.0.225/30 broadcast 12.0.0.227 
 inet6 2001:cafe:0:38::1/64 
 inet6 fe80::4638:39ff:fe00:388/64 
cumulus@switch:$ ip addr show | grep swp8 
 10: swp8: <BROADCAST,MULTICAST,UP,LOWER_UP> 
  mtu 1500 qdisc pfifo_fast state UP qlen 500 
  inet 12.0.0.225/30 brd 12.0.0.227 scope global swp8 
 104: swp8.2049@swp8: <BROADCAST,MULTICAST,UP,LOWER_UP> 
  mtu 1500 qdisc noqueue state UP 
  inet 12.0.0.229/30 brd 12.0.0.231 scope global swp8.2049 
 105: swp8.2050@swp8: <BROADCAST,MULTICAST,UP,LOWER_UP> 
  mtu 1500 qdisc noqueue state UP 
  inet 12.0.0.233/30 brd 12.0.0.235 scope global swp8.2050 
 106: swp8.2051@swp8: <BROADCAST,MULTICAST,UP,LOWER_UP> 
  mtu 1500 qdisc noqueue state UP 
  inet 12.0.0.237/30 brd 12.0.0.239 scope global swp8.2051 
 107: swp8.2052@swp8: <BROADCAST,MULTICAST,UP,LOWER_UP> 
  mtu 1500 qdisc noqueue state UP 
  inet 12.0.0.241/30 brd 12.0.0.243 scope global swp8.2052 
 108: swp8.2053@swp8: <BROADCAST,MULTICAST,UP,LOWER_UP>
  mtu 1500 qdisc noqueue state UP 
  inet 12.0.0.245/30 brd 12.0.0.247 scope global swp8.2053 
 109: swp8.2054@swp8: <BROADCAST,MULTICAST,UP,LOWER_UP> 
  mtu 1500 qdisc noqueue state UP 
  inet 12.0.0.249/30 brd 12.0.0.251 scope global swp8.2054
 110: swp8.2055@swp8: <BROADCAST,MULTICAST,UP,LOWER_UP>
  mtu 1500 qdisc noqueue state UP 
  inet 12.0.0.253/30 brd 12.0.0.255 scope global swp8.2055
cumulus@switch:$ bgp sessions: 
 12.0.0.226 ,4 ,64057 , 958 , 1036 , 0 , 0 , 0 ,15:55:42, 0, 10472 
 12.0.0.230 ,4 ,64058 , 958 , 1016 , 0 , 0 , 0 ,15:55:46, 187, 10285
 12.0.0.234 ,4 ,64059 , 958 , 1049 , 0 , 0 , 0 ,15:55:40, 187, 10285 
 12.0.0.238 ,4 ,64060 , 958 , 1039 , 0 , 0 , 0 ,15:55:45, 187, 10285 
 12.0.0.242 ,4 ,64061 , 958 , 1014 , 0 , 0 , 0 ,15:55:46, 187, 10285 
 12.0.0.246 ,4 ,64062 , 958 , 1016 , 0 , 0 , 0 ,15:55:46, 187, 10285 
 12.0.0.250 ,4 ,64063 , 958 , 1029 , 0 , 0 , 0 ,15:55:43, 187, 10285 
 12.0.0.254 ,4 ,64064 , 958 , 1036 , 0 , 0 , 0 ,15:55:44, 187, 10285

RN-398 (CM-10379)		 While upgrading Cumulus RMP, a prompt to configure grub-pc appears

While upgrading to the latest version of Cumulus RMP from version 2.5.5 or earlier, a prompt appears, asking you to choose onto which partitions to install the GRUB boot loader. 

... 

  1. /dev/mmcblk0 (3783 MB; ???)       3. /dev/dm-2 (1610 MB; CUMULUS-SYSROOT1)
  2. - /dev/mmcblk0p3 (268 MB; /boot)  4. none of the above

(Enter the items you want to select, separated by spaces.)

GRUB install devices:

...

This prompt should not appear, and the issue will be fixed in a future release.

In the meantime, to work around this issue, choose option 1, /dev/mmcblk0 and continue the upgrade.

RN-597 (CM-15705)		 sFlow doesn't generate flow samples to sflowd on Tomahawk-based switches At this time, sFlow is not supported on switches with Tomahawk ASICs. This is a known issue. 

RN-599 (CM-15949)		 DHCRELAY automatically binds to eth0 when not specified in the configuration dhcrelay listens for all interfaces that have an IP, even if not configured to listen for that interface. This causes dhcrelay to bind to unspecified ports.

This behavior is expected, due to upstream configuration. The packet is dropped later in the process, as it is not coming from a configured port.

RN-602 (CM-)		 sFlow ifSpeed incorrect in counter samples

Counter samples for an 80G bond (2 x 40G) exported from the switch show an interface speed (ifSpeed) of 14.464Gbps.

This issue is currently being investigated.

RN-605 (CM-15515)		 Unable to change the bond-modes using ifup or ifreload When the bond mode is changed from 802.3ad to balance-xor or vice versa using ifup bondx or ifreload -a, the bond-mode does not change, and the following error is produced: 
2017-03-23 21:39:37,495:  DEBUG:      autolib.netobjects: [cumulus@127.0.0.1:1042] sudo: ('ifup bond1',)
2017-03-23 21:39:37,926:  DEBUG:      autolib.netobjects: warning: error writing to file /sys/class/net/bond1/bonding/mode([Errno 39] Directory not empty)

This issue is being addressed in a later release.
Have more questions? Submit a request

Comments

Powered by Zendesk